|
|
|
| |
|
| |
| The humidity controller is designed specifically
for the control of plant growth and related
environments. Easy to set and operate. The
anodized aluminum enclosure provides a durable
and attractive housing which will never corrode
or discolor from hot, cold or humid environments.
The large dial face is easy to read and adjust.
This unit can be used independently or as
part of a combination of control devices to
coordinate numerous atmospheric functions.
This controller can be switch from humidify
to dehumidify with a stroke of the finger. |
|
| |
| |
|
| Image: |
|
| Description: |
| Control humidity automatically and
accurately with Green Air Products Total
Humidity Controller. The THC can
be switched between humidify and dehumidify
for removing unwanted atmospheric moisture
accumulating within an enclosed area
or to add needed moisture to the air
by means of humidification. The THC-1
humidity switch controls humidity equipment
by providing power when humidity varies
from the adjustable set point.
In the dehumidifying mode high humidity
conditions will activate fans or other
dehumidifying apparatus until level
drops approximately 5%. At this point
dehumidifying equipment is disabled
until humidity increases again 5%. |
| In the humidifying mode this control
operates fogging or other humidifying
equipment by activating switches, motors,
valves or pumps. Humidifiers can be
precisely controlled according to atmospheric
humidity to create ideal conditions
for any environment. The 110V outlet
receptacle receives power when atmospheric
moisture content becomes less then your
preset minimum allowable percentage.
Switches 120V at 15 amp maximum.
Sensor allows a 5% (differential)
comfort zone between "on" and "off"
functions.
If your humidifier or dehumidifier
already has a humidity control, turn
it to full on position and set the
humidity dial to your minimum desired
level. The THC-1 can also be used
with many other types of humidity
equipment or any other electrically
triggered appliances. |
|
| 
|
|
Basic operation to exhaust
excess humidity.
Could also be controlling a
dehumidifier. |
|
| Basic set-up to use for humidification
control. Could also be used
with a misting system. |
|
|
Combination
Power-Cord |
 |
| All Control Stats utilize a
duplex cord-cap which provides a combination
plug and receptacle power cord design.
Insert plug into 110V wall outlet and
plug equipment into piggy back receptacle. |
|
|
| |
| |
|
| Image: |
|
| Description: |
| The RHC Relative Humidity
Controller is our most recent
development in total humidity
control. It is switchable between
humidify and dehumidify. The
RHC has a built- in onboard
sensor which is accurate within
+/- 5% with a set differential
of 5%. Perfect for plant zone
environments, reptile habitats,
or just about any application
requiring accurate response
and control. Plug your
humidity equipment into the
120 volt 3 prong piggy-back
cord. |
|
|
| |
|
| Image: |
|
| Description: |
The RHC(R) is similar
to the RHC except it is designed
with a 20 ft. remote sensor.
Both units operate equipment
up to 15 amps at 120 volt. |
|
|
| Features: |
- Microprocessor controlled for
improved accuracy
- Accurate control between 5-95%
RH with a 5% differential for improved
response
- Relative humidity with built-in
temperature compensation
- Perfect for fogged gardens and
greenhouses
- Humidify or dehumidify with the"push
of a button"
- Fully integrable with other atmospheric
controls & timers
- Available with "on-board" humidity
sensor or 20-foot patch-cord with
"remote" sensor
- Anodized, black, aluminum chassis
resists rusting, corrosion &
scratching
- Red, illuminated power switch
- 14 AWG, SJTW rated, piggy-back
power cord
- Operates on 120 VAC with 15 Amp
switching capacity
- 30 Amp relay for reliability
- Manufactured in Oregon, USA
|
|
| Specifications: |
- Humidistat Range: 5-95% RH
- Humidistat Differential: 5% RH
- Operating Temperature: 32-120ºF
(0-50ºC)
- Operating Humidity: Non-Condensing
Environment (0-95% RH)
- Voltage Input: 120 VAC
- Voltage Output: 120 VAC
- Max Amperage Rating: 15 AMPS
- Frequency: 60 Hz
- Dimensions: 4" Wide x 5-7/8" High
x 2¼" Deep (10cm x 15cm x 6cm)
- Power Cord: 6-ft, piggy-back 14
awg, SJTW rated
- External Sensor Connection: Std
RJ-11 patchcord
|
|
|
| |
|
